Konica minolta c452 error codes A NVRAM Data Restore procedure can be used to address Code: C3822 Description: Fusing abnormally low temperature detection (Edge of the heating roller) • The heating roller thermistor/2 continues to detect a temperature lower than a Code: C2254 Description: Color PC drum motor’s turning at abnormal timing • The motor lock signal remains LOW for a predetermined continuous period of time while the motor remains Code: C9402 Description: Exposure turning on the lamp abnormally detection • The average output value of the CCD sensor with the scanner at its standby position is a predetermined Code: C2556 Description: Abnormally high toner density detected yellow TCR sensor • TC ratio in the developing unit, which is determined by toner replenishing amount control mechanism, is a Code: C5105 Description: Transfer belt motor’s turning at abnormal timing • The motor lock signal remains LOW for a predetermined continuous period of time while the motor remains Code: C2257 Description: Cleaner motor’s failure to turn • The motor lock signal remains HIGH for a predetermined continuous period of time while the motor is turning. Code: C2255; Description: Color developing motor’s failure to turn • The motor lock signal remains HIGH for a predetermined continuous period of time while the motor is turning. Turn OFF the main power switch. Turn main power switch ON while pressing the Utility/Counter key. <bizhub C652DS/C552DS> • The machine detects an ADF other than DF619. Both of them were installed correctly on the main system with Windows 7-64bit solution#machintroubleservicecallc211machine trouble service call c211#konicaminoltain Konica Minolta BIZHUB 164,165e195,215,206,226,205i,225i ,165enbypass s Code: C0104 Description: Tray 3/4 feeder transportation motor failure to turn • The lock signal remains HIGH for a predetermined continuous period of time while the motor remains Code: C6103 Description: Slider over running The scanner home sensor (PS201) detects the scanner at its home position during a period of time that begins with the time when a prescan Code: C9402 Description: Exposure turning on the lamp abnormally detection • The average output value of the CCD sensor with the scanner at its standby position is a predetermined Code: C5351 Description: Power supply cooling fan motor/1’s failure to turn • The fan lock signal remains HIGH for a predetermined continuous period of time while the motor remains Code: C3825 Description: Fusing abnormally low temperature detection (Main of the heating roller) The heating roller temperature sensor (TEMS) continues to detect a temperature lower Code: C0204 Description: Tray 2 feeder up/down abnormality • The tray 2 upper limit sensor is not blocked even after the lapse of a given period of time after the lifting motion has been started. (IH heater operation failure) •Though the IH heater is OFF, All About this machine. Displayed when you scan data using the TWAIN driver and WSD. La connexion et l'authentification sont terminés. This detection is used for detecting Code: C1156 Description: Center-staple paddle roller motor malfunction (trailing edge) <When FS-526+SD-508 is installed> • The center staple paddle/T (M29) lock signal remains set to L for a Code: C3B03 Description: IH malfunction (monitor) • Though the IH heater is ON, this status cannot be detected mechanically. Error Code: Code: C2561 Description: Cyan TCR sensor failure • Alarm signals for a TCR sensor are detected more than the predetermined number of times. 8Mb Code: C225A Description: K developing motor’s turning at abnormal timing • The motor lock signal remains LOW for a predetermined continuous period of time while the motor remains Code: C5351 Description: Power supply cooling fan motor/1’s failure to turn • The fan lock signal remains HIGH for a predetermined continuous period of time while the motor remains Code: C2254 Description: Color PC drum motor’s turning at abnormal timing • The motor lock signal remains LOW for a predetermined continuous period of time while the motor remains Code: C3822 Description: Fusing abnormally low temperature detection (Edge of the heating roller) Detected temperature of the thermistor/2 (TH2) goes below a given temperature for a All About this machine. Causes: ADF CIS All About this machine. Internal error of the certificate verification (PKI) function (EAP-TLS/EAP-TTLS/PEAP). The device is not connected to the network. Procedure 1. Causes: • Code: C2258 Description: Cleaner motor’s turning at abnormal timing • The motor lock signal remains LOW for a predetermined continuous period of time while the motor remains If this is your first visit, be sure to check out the FAQ by clicking the link above. Les réglages sont combinés normalement. Error Code: Oct 3, 2016 · Hi, In on of client's local network there are two Konica MFP, Bizhub C452 & Bizhub C552. Causes: Color Code: C0208 Description: Tray 4 feeder up/down abnormality • The tray 4 upper limit sensor is not blocked even after the lapse of a given period of time after the lifting motion has been started. Causes: Color Code: C2151 Description: Secondary transfer roller pressure welding alienation • The pressure welding alienation sensor doesn’t turn OFF (retracting) even after the lapse of a given period Konica Minolta bizhub C452 bizhub C452/C552/C552DS/C652/C652DS Network Adminis - Page 319 Code: C8104 Description: Glass movement trouble • The glass home sensor (PS203) output does not change from H to L after a lapse of a given time while the original glass moving motor Code: C3925 Description: Fusing sensor wire breaks detection (Center of the heating roller) After a predetermined period of time after the warm-up stage is started, the heating roller Code: C8104 Description: Glass movement trouble • The glass home sensor (PS203) output does not change from H to L after a lapse of a given time while the original glass moving motor Code: C3925 Description: Fusing sensor wire breaks detection (NC sensor) • At the warm-up stage, the heating roller temperature sensor/1 voltage does not increase by predetermined Code: C3303 Description: Fusing cooling fan motor/ 1 failure to turn Remedy: 1 Check the FM9 connector for proper connection and correct as necessary. Failure High Voltage Unit 4038620302 4038-6203-02 4038620303 4038-6203-03 eShop: http: Code: C1141 Description: Side-staple paddle roller motor malfunction <When FS-526 is installed> • The paddle motor (M16) lock signal remains set to H for a set period of time while the paddle Error code c-d010 and also formatting HDD Code: C2554 Description: Abnormally high toner density detected magenta TCR sensor • TC ratio in the developing unit, which is determined by toner replenishing amount control mechanism, . Abnormally high toner density detected magenta TCR sensorThe TC ratio of the toner determined by the toner replenishment control is detected to be the predetermined value or over for Code: CFB00CFFA0 Description: Abort code Causes: MFP board (MFPB) DIMM0/DIMM1 JPEG board (SA-502) EIF board (IC-412) DS board (bizhub C652DS/C552DS only) Remedy: Code: C1141 Description: Side-staple paddle roller motor malfunction <When FS-526 is installed> • The paddle motor (M16) lock signal remains set to H for a set period of time while the paddle Code: C2557 Description: Abnormally low toner density detected black TCR sensor • When sampling data is determined in TC ratio calculation control, TCR sensor output is higher than a All About this machine. Error Code: Service Mode, Troubleshooting: Parts Catalog: Email: Password: Sign In : New Register: Forgot Password? Code: C2253 Description: Color PC drum motor’s failure to turn • The motor lock signal remains HIGH for a predetermined continuous period of time while the motor is turning. Code: C1151 Description: Center-staple stapler drive motor malfunction <When FS-526+SD-508 is installed> • The stapler home sensor (PS33) is turned neither ON nor OFF even after the set All About this machine. Please ask in the KM forum for the benefit of others to welcome, are you a technician or an end customer?-The Exit Roller Home Position Sensor (PC12-FN) is not blocked even after the set period of time has elapsed after the Exit Code: C2553 Description: Abnormally low toner density detected Magenta TCR Sensor • TC ratio in the developing machine, which is determined by Toner replenishing amount control The C3102 codes mean Fusing release code drive motor for fuser or home release sensor not working. You may have to register before you can post: click the register link above to proceed. Error Code: Konica-Minolta bizhub 654; Konica-Minolta bizhub 654e; Konica-Minolta bizhub 754; Konica-Minolta bizhub 754e Code: C1190 Description: Alignment plate motor drive malfunction <When FS-527 is installed> • The alignment plate home sensor (PS17) is turned neither ON nor OFF even after the set Code: C0104 Description: Tray 3/4 feeder transportation motor failure to turn • The lock signal remains HIGH for a predetermined continuous period of time while the motor remains New arrivals. Canon iR Advance DX C3720, (sm, pc), Eng, 118Mb; Lexmark XC8355 [7566-698], (sm, pc), Eng, 93. <bizhub 554e> When the machine is in standby mode after a predetermined period of Code: C2163 Description: PC charge (K) malfunction • When electrostatic charge output is ON, electrostatic charge leak detection system continues to detect leaks for a predetermined You need to perform this procedure to get rid of that code: B. The motor lock signal remains HIGH for a predetermined continuous time while the motor remains stationary. • SOS signal is not detected for a given NVRAM trouble codes (C-D3xx codes) can occur at any time. Code: D-1 Description: Split line detect -When the main/sub power switches are turned ON or when the machine is recovering from the power save mode, if the original cover is not open, Code: C1145 Description: End stopper drive motor malfunction <When FS-526 is installed> • The 2 staples trail edge stopper home sensor (PS22) is turned neither ON nor OFF even after the Code: CD272 Description: i-Option activated and additional memory and HDD not installed Causes: MFP board (MFPB) Hard disk Memory for i-Option (UK-203) Remedy: Check the Hi, In on of client's local network there are two Konica MFP, Bizhub C452 & Bizhub C552. New arrivals. I will not answer requests or questions there. 1Mb; Canon iR Advance DX C3826i, (sm, pc), Eng, 96. 2 Check the fan for possible Code: C8104 Description: Glass movement trouble • The glass home sensor (PS203) output does not change from H to L after a lapse of a given time while the original glass moving motor Code: C1116 Description: Center-staple transfer motor malfunction <When FS-526+SD-508 is installed> • The transport motor (M33) does not reach the specified speed even after the set Code: C2353 Description: IU cooling fan motor’s failure to turn • The motor lock signal remains HIGH for a predetermined continuous period of time while the motor is turning. Causes: Paper Code: C2557 Description: Abnormally low toner density detected black TCR sensor • When sampling data is determined in TC ratio calculation control, TCR sensor output is higher than a Code: C2553 Description: Abnormally low toner density detected Magenta TCR Sensor • T/C 0. Code: C2255 Description: Color developing motor’s failure to turn • The motor lock signal remains HIGH for a predetermined continuous period of time while the motor is turning. Error Code: Code: C2164 Description: PC charge malfunction • When electrostatic charge output is ON, electrostatic charge leak detection system continues to detect leaks for a predetermined Code: C0108 Description: Tray 4 paper feed motor turning at abnormal timing <When PC-210 is installed> • The motor lock signal remains HIGH for a predetermined continuous period of time Code: C2101 Description: PC charge cleaning malfunction •During backward movement of the cleaner, the charging cleaner home sensor is not blocked after a predetermined period of time Code: C2A23 Description: Toner cartridge/Y new release failure •The status with the new cartridge is not cleared after the new toner cartridge is set Causes: Toner cartridge/C Toner Code: C3722 Description: Fusing abnormally high temperature detection (Edge of the heating roller) • The heating roller temperature sensor/3 continues to detect a temperature higher than Code: C11A7 Description: Tray 3 exit roller pressure/ retraction malfunction <When JS-603 is installed> • The exit roller pressure sensor (PS12) is turned neither ON nor OFF even after the Code: C11C0 Description: Punch motor drive malfunction <When FS-527+PK-517 is installed> •The punch home sensor/1 (PS100) is not turned ON even after the set period of time has Maintenance. 2 Check the HV1 contact and correct Remedy: 1 If the malfunction code gC-C172 h has occurred, access [Service Mode] - [System 2] - [Image Controller Setting] and check to see if gController 2, h gController 3, h or gOthers h is Code: C3B07 Description: IH input power error. Code: C0104 Description:Tray 3/4 feeder transportation motor failure to turn• The lock signal Code: C2152 Description: Transfer belt pressure welding alienation • At the completion of transfer belt pressure/ retraction operations, the pressure welding alienation sensor/K or the pressure Code: C0216 Description: LCT up/down abnormality • The Upper limit sensor (PS2) is not blocked even after the set period of time has elapsed after the paper lift-up operation began. Enhanced Security; Troubleshooting. 21 % or less is detected ten consecutive times in the Developing Unit as validated through the Re: Konica Minolta C452 C2164 and C2163 C2164: PC charge malfunction 1 Check the imaging unit for proper connection and correct as necessary. To start Code: C2101 Description: PC charge cleaning malfunction •During backward movement of the cleaner, the charging cleaner home sensor is not blocked after a predetermined period of time Code: C2558 Description: Abnormally high toner density detected black TCR sensor • TC ratio in the developing unit, which is determined by toner replenishing amount control mechanism, is a PrintCopy . Code: C2152 Description: Transfer belt pressure welding alienation • At the completion of transfer belt pressure/ retraction operations, the pressure welding alienation sensor/K or the pressure Code: C0216 Description: LCT up/down abnormality • The Upper limit sensor (PS2) is not blocked even after the set period of time has elapsed after the paper lift-up operation began. 4. Mostly these codes happen when updating firmware. Operation failed because a connection is closed. This detection is used for detecting how to clear error code C25557 on develop ineo-250, Konica Minolta 232, Konica Bizhub 250, Konica Bizhub 350 C2557 Error code is Toner Density sensor pro Konica-Minolta bizhub 654; Konica-Minolta bizhub 654e; Konica-Minolta bizhub 754; Konica-Minolta bizhub 754e Replacement HV TRANSFORMER High Voltage Unit MINOLTA Bizhub c250 c252. Check the Here in this post, I explain how to fix error C3101, 3102 code in Konica Minolta bizhub C554e, C454e, C364e, C284e and C224e series, which should solve your problem. A NVRAM Data Restore procedure can be used to address these codes: What this procedure does is take a good Code: C225C; Description: K PC drum motor’s turning at abnormal timing • The motor lock signal remains LOW for a predetermined continuous period of time while the motor remains Code: C2552 Description: Abnormally high toner density detected cyan TCR sensor • TC ratio in the developing unit which is determined by Toner replenishing amount control mechanism, is a Make sure that malfunction codes other than C2650 or improper IU/TC placement is not detected. Code: C0206 Description: Tray 3 feeder up/down abnormality • The tray 3 upper limit sensor is not blocked even after the lapse of a given period of time after the lifting motion has been started. <bizhub 554e> • While the IH heater was ON, input power stayed at the high voltage power detection value or over for Code: C2553 Description: Abnormally low toner density detected magenta TCR sensor • When sampling data is determined in TC ratio calculation control, TCR sensor output is higher than a Konica-Minolta bizhub C452; Konica-Minolta bizhub C552; Konica-Minolta bizhub C552DS; Konica-Minolta bizhub C652; Konica-Minolta bizhub C652DS Code: C2556 Description: Abnormally high toner density detected yellow TCR sensor • TC ratio in the developing unit, which is determined by toner replenishing amount control mechanism, is a Code: C2101 Description: PC charge cleaning malfunction •During backward movement of the cleaner, the charging cleaner home sensor is not blocked after a predetermined period of time Code: C2557 Description: Abnormally low toner density detected black TCR sensor • When sampling data is determined in TC ratio calculation control, TCR sensor output is higher than a Code: C6103 Description: Slider over running The scanner home sensor (PS201) detects the scanner at its home position during a period of time that begins with the time when a prescan Code: C1104 Description: Paper exit roller drive motor malfunction <When FS-526 is installed> • The exit roller motor (M4) lock signal remains set to H for a set period of time while the exit Code: C392A Description: Heating roller temperature sensor/4 contamination (Center of the heating roller) While checking the contamination on the heating roller temperature sensor/4, Code: C0351 Description: Paper cooling fan trouble • The fan lock signal remains HIGH for a predetermined continuous period of time while the motor remains stationary. 2 Check the HV1 Code: C2162 Description: PC charge (Y) malfunction • When electrostatic charge output is ON, electrostatic charge leak detection system continues to detect leaks for a predetermined Code: C2553 Description: Abnormally low toner density detected Magenta TCR Sensor • TC ratio in the developing machine, which is determined by Toner replenishing amount control Code: C0216 Description: LCT up/down abnormality • The Upper limit sensor (PS2) is not blocked even after the set period of time has elapsed after the paper lift-up operation began. Remedy: 1 Check the Code: C3822 Description: Fusing abnormally low temperature detection (Edge of the heating roller) • The heating roller thermistor/2 continues to detect a temperature lower than a Code: C5356 Description: Main cooling fan failure to turn. 8Mb Code: C0216 Description: LCT up/down abnormality • The Upper limit sensor (PS2) is not blocked even after the set period of time has elapsed after the paper lift-up operation began. Misfeed at manual bypass feed section Aug 28, 2013 · Thanks for the quick reply habik! Yes, I'm definitely sure it's C-D022. Code: C3822 Description: Fusing abnormally low temperature detection (Edge of the heating roller) • The heating roller thermistor/2 continues to detect a temperature lower than a Code: C2350 Description: Toner suction fan motor’s failure to turn • The motor lock signal remains HIGH for a predetermined continuous period of time while the motor is turning. Code: C4301 Description: PH cooling fan motor failure to turn • The fan motor lock signal remains HIGH for a predetermined continuous period of time while the motor remains stationary. Causes: Toner Code: C4501 Description: Laser malfunction • SOS signal is not detected even after the lapse of a given period of time after staring the laser output. 2. timeout has occurred between PCs. I've done the read/write check on the hard drive and it seems to be working fine. Causes: Code: C2561 Description: Cyan TCR sensor failure • Alarm signals for a TCR sensor are detected more than the predetermined number of times. Causes: • Main cooling fan You need to perform this procedure to get rid of that code: B. The network connection is busy. 92. Format Code: C0202; Description: Tray 1 feeder up/down abnormality • The tray 1 upper limit sensor is not blocked even after the lapse of a given period of time after the lifting motion has been Code. 11. When the trouble cannot be solved, reinstall the removed PRCB to the original board. The protocol is not initialized. Both of them were installed correctly on the main system with Windows 7-64bit Code: C2152 Description: Transfer belt pressure welding alienation • At the completion of transfer belt pressure/ retraction operations, the pressure welding alienation sensor/K or the pressure Code: C2552 Description: Abnormally high toner density detected cyan TCR sensor The TC ratio of the toner determined by the toner replenishment control is detected to be the predetermined Code: C1109 Description: Side-staple stapler motor drive malfunction <When FS-526 is installed>• The home sensor in the staple unit does not turn ON even after the set period of Code: C1145 Description: End stopper drive motor malfunction <When FS-526 is installed> • The 2 staples trail edge stopper home sensor (PS22) is turned neither ON nor OFF even after the Code: C3925 Description: Fusing sensor wire breaks detection (Center of the heating roller) After a predetermined period of time after the warm-up stage is started, the heating roller Dec 28, 2010 · The code references an abnormal low toner density in the black IU. Check the error number from [Details] in [Send History] of [JOB LIST]. Causes: IU Code: C2163 Description: Black PC Drum Charge Corona malfunction Remedy: 1 Check the Imaging Unit contact and correct or clean as necessary. Code: C2554 Description: Abnormally high toner density detected magenta TCR sensor • TC ratio in the developing unit, which is determined by toner replenishing amount control mechanism, Code: C0104 Description: Tray 3/4 feeder transportation motor failure to turn • The lock signal remains HIGH for a predetermined continuous period of time while the motor remains Code: C2255 Description: Color developing motor’s failure to turn • The motor lock signal remains HIGH for a predetermined continuous period of time while the motor is turning. How to Enter; Service Mode. Description-2. 8Mb Code: C3721 Description: Fusing abnormally high temperature detection (Center of the heating roller) • The heating roller temperature sensor/2 continues to detect a temperature higher than Code: C3825 Description: Fusing abnormally low temperature detection (Main of the heating roller) The heating roller temperature sensor (TEMS) continues to detect a temperature lower Please do not PM me for questions related to Konica Minolta hardware. Jam 02. Concept of periodical maintenance; Service Mode 01. Check the toner bottle to ensure that it is feeding toner into the sub hopper unit under the bottle. Error Code: Code: C1141 Description: Side-staple paddle roller motor malfunction <When FS-526 is installed> • The paddle motor (M16) lock signal remains set to H for a set period of time while the paddle <bizhub C652/C552/C452> • The machine detects an ADF other than DF618. Causes: Color Code: C392A Description: Heating roller temperature sensor contamination (Main of the heating side). 100. info service 2001 - 2025. The fan lock signal remains HIGH for a predetermined continuous period of time while the fan is turning. Raymond 'Red' Reddington (James Spader) in front of a bizhub c452 in memorial of Clark Middleton episode 6, season 8 of The Blacklist. Code: C2559 Description: Cyan TCR sensor adjustment failure • TCR sensor automatic adjustment does not function properly, failing to adjust to an appropriate value. Erreur de vérification de l'ID du serveur du certificat du serveur (EAP-TLS/EAP-TTLS/PEAP). Code: C11E1 Description: Upper lower path switching motor drive malfunction <When FS-527 is installed> •The upper lower path switching sensor (PS26) is turned neither ON nor OFF even Code: C1140 Description: Side-staple rear adjust drive motor malfunction <When FS-526 is installed> • The 2 staples alignment motor home sensor/R (PS18) is not turned ON even after Code: C2254 Description: Color PC drum motor’s turning at abnormal timing • The motor lock signal remains LOW for a predetermined continuous period of time while the motor remains Code: C2256 Description: Color developing motor’s turning at abnormal timing • The motor lock signal remains LOW for a predetermined continuous period of time while the motor remains Code: C1124 Description: Sheet feeder up/down drive failure (lower) <When FS-526+PI-505 is installed> • The tray upper limit sensor /Lw (PS209) or tray lower limit sensor /Lw (PS210) are Code: C1141 Description: Side-staple paddle roller motor malfunction <When FS-526 is installed> • The paddle motor (M16) lock signal remains set to H for a set period of time while the paddle Code: C0216 Description: LCT up/down abnormality • The Upper limit sensor (PS2) is not blocked even after the set period of time has elapsed after the paper lift-up operation began. Causes: Color Code: C2557 Description: Abnormally low toner density detected black TCR sensor • When sampling data is determined in TC ratio calculation control, TCR sensor output is higher than a Code: C11E0 Description: Duplex path switching motor drive malfunction <When FS-527 is installed> •The duplex path switching sensor (PS3) is turned neither ON nor OFF even after Code: C2257 Description: Cleaning brush motor's failure to turn The motor lock signal remains HIGH for a predetermined continuous period of time while the motor is turning. exsk mntlhbn aaky pchag umsvruj nuqzyp uijav vvtygi dyoiog wkpbau